bcm63xx/u-boot/configs/meesc_dataflash_defconfig, branch master

Convert CONFIG_ENV_SPI_* to Kconfig

2019-03-25T21:36:59Z

This converts the following to Kconfig: CONFIG_ENV_SPI_BUS CONFIG_ENV_SPI_CS CONFIG_ENV_SPI_MAX_HZ CONFIG_ENV_SPI_MODE Most of time these value are not needed, CONFIG_SF_DEFAULT with same value is used, so I introduced CONFIG_USE_ENV_SPI_* to force the associated value for the environment. Signed-off-by: Patrick Delaunay

configs: Resync with savedefconfig

2018-09-03T19:26:12Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

Convert CONFIG_MISC_INIT_R to Kconfig

2018-08-17T17:04:00Z

This converts the following to Kconfig: CONFIG_MISC_INIT_R Signed-off-by: Adam Ford [trini: Update the defaults logic slightly] Signed-off-by: Tom Rini

configs: Migrate CONFIG_NR_DRAM_BANKS

2018-08-16T20:45:02Z

We have the following cases: - CONFIG_NR_DRAM_BANKS was defined, migrate normally - CONFIG_NR_DRAM_BANKS_MAX was defined and then used for CONFIG_NR_DRAM_BANKS after a check, just migrate it over now. - CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 + 2), set this to 8. Signed-off-by: Tom Rini

Convert CONFIG_SPI to Kconfig

2018-04-27T18:54:11Z

This converts the following to Kconfig: CONFIG_SPI This partly involves updating code that assumes that CONFIG_SPI implies things that are specific to the MPC8xx SPI driver. For now, just update the CONFIG tests. This also involves reworking the default for CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a reasonable default, as it does not cause any compile failures. Signed-off-by: Adam Ford Signed-off-by: Tom Rini

configs: Resync with savedefconfig

2018-04-17T14:10:47Z

Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini

spi: atmel: default y if DM_SPI && ARCH_AT91

2018-04-06T20:11:09Z

ATMEL_SPI is now fully converted to driver-model and respective boards switch to DM_SPI as well, so make default y for ARCH_AT91 Signed-off-by: Jagan Teki Acked-by: Wenyou Yang

Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig

2018-02-24T02:41:49Z

This converts the following to Kconfig: CONFIG_BOOTP_BOOTPATH CONFIG_BOOTP_DNS CONFIG_BOOTP_GATEWAY CONFIG_BOOTP_HOSTNAME CONFIG_BOOTP_PXE CONFIG_BOOTP_SUBNETMASK CONFIG_CMDLINE_EDITING CONFIG_AUTO_COMPLETE CONFIG_SYS_LONGHELP CONFIG_SUPPORT_RAW_INITRD CONFIG_ENV_VARS_UBOOT_CONFIG Signed-off-by: Adam Ford [trini: Re-run the migration] Signed-off-by: Tom Rini

configs: Migrate CONFIG_SYS_TEXT_BASE

2018-02-11T14:30:09Z

On the NIOS2 and Xtensa architectures, we do not have CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current values into the defconfig and removing them from the headers. I did not attempt to add more default values in and for now will leave that to maintainers. Signed-off-by: Tom Rini

cmd: Make CONFIG_CMD_FPGA depend on CONFIG_FPGA

2018-02-06T01:58:11Z

cmd/Makefile has: ifdef CONFIG_FPGA obj-$(CONFIG_CMD_FPGA) += fpga.o endif which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently does nothing. Let's remove that Makefile conditional and instead express this equivalent dependency in Kconfig, so a lot of redundant # CONFIG_CMD_FPGA is not set can be removed from board defconfigs that don't actually have an FPGA. Signed-off-by: Tuomas Tynkkynen