staging/ynezz/target/linux, branch master

kernel: backport fix for hang on napi_disable with threaded NAPI

2021-06-01T21:20:07Z

Signed-off-by: Felix Fietkau

layerscape: refresh kernel config

2021-05-30T00:21:02Z

Run `make kernel_oldconfig CONFIG_TARGET=subtarget` This mostly aims at getting rid of redundant/unneeded symbols. Signed-off-by: Adrian Schmutzler

kernel: add missing symbol CONFIG_AHCI_XGENE

2021-05-30T00:21:02Z

Add missing symbol CONFIG_AHCI_XGENE. Signed-off-by: Yangbo Lu [also add for 5.10, remove from layerscape target config] Signed-off-by: Adrian Schmutzler

kernel: bump 5.4 to 5.4.123

2021-05-29T16:31:49Z

All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia

ramips: add support for Wavlink WL-WN578A2

2021-05-27T23:12:21Z

This commit adds support for the Wavlink WL-WN578A2 dual-band wall-plug wireless router. This device is also sold under the name SilverCrest SWV 733 A2. Device Specifications: - CPU: MediaTek MT7628AN (580MHz) - Flash: 8MB - RAM: 64MB - Bootloader: U-Boot - Ethernet: 2x 10/100 Mbps - 2.4 GHz: 802.11b/g/n SoC - 5 GHz: 802.11a/n/ac MT7610E - Antennas: internal - 4 green LEDs: WPS/Power, LAN, WAN, wifi-low, wifi-med, wifi-high - Buttons: Reset, WPS - Sliding mode switch: AP, repeater, client - Small sliding power switch Flashing instructions: U-Boot launches TFTP client if WPS button is pressed during power-on. Configure as follows: - Server IP: 192.168.10.100 - Filename (rename sysupgrade file to this): firmware.bin Flashing should not take more than a minute, device will reboot automatically. Signed-off-by: Thomas Aldrian

kernel: bump 5.10 to 5.10.40

2021-05-27T17:32:10Z

Automatically refreshed: generic/hack-5.10/902-debloat_proc.patch generic/pending-5.10/110-perf-jevents-fix-getting-maximum-number-of-fds.patch Signed-off-by: Rui Salvaterra

base-files: generate network config with "device" options

2021-05-27T08:58:49Z

Replace "ifname" with "device" as netifd has been recently patches to used the later one. It's more clear and accurate. Signed-off-by: Rafał Miłecki

ath79: add missing v5.4 SPI chipselect patch

2021-05-26T21:11:00Z

The patch was not applied to the v5.4 target, thus breaking Kernel 5.4 on devices with multiple flash chips attache to the SPI bus. Fixes commit bd54e739541b ("ath79: set number of chipselect lines") Signed-off-by: David Bauer

ramips: add support for JCG Q20

2021-05-26T21:10:45Z

JCG Q20 is an AX 1800M router. Hardware specs: SoC: MediaTek MT7621AT Flash: Winbond W29N01HV 128 MiB RAM: Winbond W632GU6NB-11 256 MiB WiFi: MT7915 2.4/5 GHz 2T2R Ethernet: 10/100/1000 Mbps x3 LED: Status (red / blue) Button: Reset, WPS Power: DC 12V,1A Flash instructions: Upload factory.bin in stock firmware's upgrade page, do not preserve settings. MAC addresses map: 0x00004 *:3e wlan2g/wlan5g 0x3fff4 *:3c lan/label 0x3fffa *:3c wan Signed-off-by: Chukun Pan

ramips: add support for cudy WR2100

2021-05-26T21:10:37Z

Specifications SoC: MT7621 CPU: 880 MHz Flash: 16 MiB RAM: 128 MiB WLAN: 2.4 GHz b/g/n, 5 GHz a/n/ac MT7603E / MT7615E Ethernet: 5x Gbit ports Installation There are two known options: 1) The Luci-based UI. 2) Press and hold the reset button during power up. The router will request 'recovery.bin' from a TFTP server at 192.168.1.88. Both options require a signed firmware binary. The openwrt image supplied by cudy is signed and can be used to install unsigned images. R4 & R5 need to be shorted (0-100Ω) for the UART to work. Signed-off-by: Leon M. George [remove non-required switch-port node - remove trgmii phy-mode] Signed-off-by: David Bauer