staging/pepe2k/package/boot, branch master

uboot-envtools: add support for Check Point V-81

2025-06-22T20:17:20Z

Add support for Check Point V-81 to add/edit bootcmd variables for booting OpenWrt. Signed-off-by: INAGAKI Hiroshi Link: https://github.com/openwrt/openwrt/pull/16904 Signed-off-by: Hauke Mehrtens

uboot-envtools: add support for Check Point V-80

2025-06-22T20:17:20Z

Add support for Check Point V-80 to add/edit bootcmd variables for booting OpenWrt. Signed-off-by: INAGAKI Hiroshi Link: https://github.com/openwrt/openwrt/pull/16904 Signed-off-by: Hauke Mehrtens

uboot-envtools: cns3xxx: remove config file

2025-06-21T11:57:06Z

This file is a leftover of cns3xxx target which has been dropped in commit a9790dff532e ("cns3xxx: drop target"). Signed-off-by: Shiji Yang Link: https://github.com/openwrt/openwrt/pull/19191 Signed-off-by: Hauke Mehrtens

sunxi: add support for OrangePi Zero 2W

2025-06-16T21:10:54Z

Specifications: SoC: Allwinner H618 SoC (Quad core Cortex-A53) DRAM: 1/1.5/2/4 GB LPDDR4 DRAM (1.5GB version not supported) Power: 5V USB-C Video: HDMI (Type 2.0A - micro) Storage: microSD / 16MByte SPI flash Network: Unisoc UWE5622 (no driver currently) Debug: serial UART Flashing instructions: Standard sunxi SD card installation procedure - copy image to SD card, insert into SD card slot on the device and boot. Signed-off-by: Zoltan HERPAI

qualcommax: ipq50xx: Add support for Xiaomi AX6000

2025-06-13T10:02:39Z

Add support for Xiaomi AX6000. Speficiations: * SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz) * Memory: Etrontech EM6HE16EWAKG 512 MiB DDR3L-933 * Serial Port: 1v8 TTL 115200n8 * Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax - up to 574 Mbps) QCN9024 (4x4 5 Ghz 802.11an/ac/ax - up to 4804 Mbps) QCA9887 (1x1 5 Ghz 802.11ac/n - up to 433 Mbps) * Ethernet: IPQ5018 integrated virtual switch connected to: - external QCA8337 switch (3 LAN Ports 10/100/1000) - QCA8081 Phy WAN port (10/100/1000/2500) * Flash: Either of: - Gigadevice GD5F1GQ4RE9IGD (128 MiB) - ESMT F50D1G41LB (128 MiB) * LEDs: 1x WLAN Link (GPIO 23 Active High) 1x System Blue (GPIO 24 Active High) 1x System Yellow (GPIO 25 Active High) 1x WAN Link Blue (GPIO 26 Active High) 1x WAN Link Yellow (GPIO 27 Active High) 1x Green - Unused(GPIO 28 Active High) 3x LAN Phy Green 1x WAN Phy Green * Buttons: 1x Reset (GPIO 38 Active Low) Known issue: - QCA9887 doesn't come up (possibly due to 1-lane PCIe phy not coming up or missing method to drive power), hence the host PCIe controller is disabled in the DTS. Flash instructions: Download XMIR Patcher: https://github.com/openwrt-xiaomi/xmir-patcher First flash a ubinized OpenWrt initramfs that will serve as the intermediate step, since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages, through either of the below two methods: Installation via XMIR Patcher: 1. Load the initramfs image: openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi Installation via ubiformat method, through SSH: 1. If needed, enable SSH using XMIR Patcher. 2. Copy the file openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi to the /tmp directory 3. Open an SSH shell to the router 4. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 5. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd18 and mtd19 are the correct indexes from above! 6. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq50xx-xiaomi_ax6000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 7. Reboot the device by: reboot Continue in order to pernamently flash OpenWrt: 1. Upload the sysupgrade image to /tmp/ using SCP: scp -O root@192.168.1.1:/tmp/ 2. Open an SSH shell to 192.168.1.1 from a PC within the same subnet 3. Use sysupgrade to flash the sysupgrade image: sysupgrade -n -v /tmp/openwrt-qualcommax-ipq50xx-xiaomi_ax6000-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: George Moussalem Link: https://github.com/openwrt/openwrt/pull/19004 Signed-off-by: Robert Marko

uboot-tools: uboot-envtools: add support for I-O DATA WN-DAX3000GR

2025-06-12T08:54:34Z

Add support for I-O DATA WN-DAX3000GR to update bootdelay variable while sysupgrade. Signed-off-by: INAGAKI Hiroshi Link: https://github.com/openwrt/openwrt/pull/19053 Signed-off-by: Robert Marko

mediatek: add support for TP-Link Archer AX80v1(US/RU/CA)

2025-06-05T20:55:55Z

This commit adds support for TP-Link Archer AX80v1(US/RU/CA). Device specification SoC Type: MediaTek MT7986AV, Cortex-A53, 64-bit RAM: ESMT M15T4G16256 (512MB) Flash: ESMT F50L1G41LB (128 MB) Ethernet: MediaTek MT7531AE + 2.5GbE MaxLinear GPY211C0VC (SLNW8) Ethernet: 1x2.5Gbe (WAN/LAN 2.5Gbps), 4xGbE (WAN/LAN 1Gbps, LAN1, LAN2, LAN3) WLAN 2g: MediaTek MT7976GN WLAN 5g: MediaTek MT7976AN LEDs: 1 red,1 green,1 blue status LEDs, Buttons: 4 (Reset,ledswitch,wps,wlan), USB ports: 1 (USB 3.0) Power: 12 VDC, 3,3 A Connector: Barrel Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI slots contain "seconduboot" (also U-Boot 2022.01-rc4) Serial console (UART) V +-------+-------+-------+-------+ | +3.3V | GND | TX | RX | +---+---+-------+-------+-------+ | +--- Don't connect Installation (UART) Place OpenWrt initramfs image on tftp server with IP 192.168.1.2 Attach UART, switch on the router and interrupt the boot process by pressing 'Ctrl-C' Load and run OpenWrt initramfs image: tftpboot initramfs-kernel.bin bootm !!Attention!! is very important! After entering OpenWrt, please set / update the environment variables: fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit" fw_setenv mtdids "spi-nand0=spi-nand0" fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data),8M(mali_data)" fw_setenv tp_boot_idx 0 Run 'sysupgrade -n' with the sysupgrade OpenWrt image from console or Luci WebUI. Recovery Press Reset button and power on the router Navigate to U-Boot recovery web server (192.168.1.1) and upload the OEM firmware Stock layout 0x000000000000-0x000000200000 : "boot" 0x000000200000-0x000000300000 : "u-boot-env" 0x000000300000-0x000003500000 : "ubi0" 0x000003500000-0x000006700000 : "ubi1" 0x000006700000-0x000006f00000 : "userconfig" 0x000006f00000-0x000007300000 : "tp_data" 0x000007300000-0x000007B00000 : "mali_data" ubi0/ubi1 format U-Boot at boot checks that all volumes are in place: +-------------------------------+ | Volume Name: uboot Vol ID: 0| | Volume Name: kernel Vol ID: 1| | Volume Name: rootfs Vol ID: 2| +-------------------------------+ MAC addresses +---------+-------------------+-----------+ | label | 00:eb:xx:xx:xx:be | label | | LAN | 00:eb:xx:xx:xx:be | label | | WAN | 00:eb:xx:xx:xx:bf | label+1 | | WLAN 2g | 00:eb:xx:xx:xx:be | label | | WLAN 5g | 00:eb:xx:xx:xx:bd | label-1 | +---------+-------------------+-----------+ label MAC address was found in UBI partition "tp_data", file "default-mac". OEM wireless eeprom is also there (file "MT7986_EEPROM.bin"). Signed-off-by: Sergey Shlukov Link: https://github.com/openwrt/openwrt/pull/17753 Signed-off-by: Hauke Mehrtens

uboot-mediatek: update patch for Cudy TR3000-v1 and SNR SNR-CPE-AX2

2025-06-03T21:24:07Z

Update the reference to gpio props. Fixes: 2a32d215ba47 ("uboot-mediatek: bump to v2025.04") Signed-off-by: Tianling Shen Link: https://github.com/openwrt/openwrt/pull/18988 Signed-off-by: Hauke Mehrtens

uboot-mediatek: bump to v2025.04

2025-05-31T19:16:41Z

The following upstreamed / superseded patches were dropped: 060-01-clk-mediatek-mt7629-fix-parent-clock-of-some-top-clo.patch 060-02-arm-dts-mt7629-fix-sgmii-clock-selection-for-etherne.patch 060-03-net-mediatek-use-correct-register-field-for-SGMII-sp.patch 060-04-net-mediatek-correct-register-name-of-ethsys-syscfg1.patch 060-05-net-mediatek-fix-sgmii-selection-for-mt7622.patch 060-06-net-mediatek-fix-gmac2-usability-for-mt7629.patch 060-07-net-mediatek-add-support-for-10GBASE-R.patch 060-08-net-mediatek-make-sgmii-usxgmii-optional.patch 060-09-net-mediatek-don-t-enable-GDMA-cpu-bridge-unconditio.patch 060-10-net-mediatek-fix-usability-with-wget-command.patch 061-01-net-mediatek-split-ethernet-switch-code-from-mtk_eth.patch 061-02-net-mediatek-add-support-for-MediaTek-MT7987-SoC.patch 061-03-net-mediatek-add-support-for-Airoha-AN8855-ethernet-.patch 070-01-board-mediatek-mt7622-remove-board_late_init.patch 070-02-clk-mediatek-fix-uninitialized-fields-issue-in-INFRA.patch 070-03-configs-mt7629-move-image-load-address-to-0x42000000.patch 070-04-configs-mt7988-move-image-load-address-to-0x44000000.patch 070-05-spi-mtk_spim-add-support-to-use-DT-live-tree.patch 070-06-spi-mtk_spim-check-slave-device-mode-in-spi-mem-s-su.patch 070-07-arm-dts-mediatek-add-quad-mode-capabilities-for-SPI-.patch 070-08-pwm-mediatek-add-pwm3-support-for-mt7981.patch 070-09-pci-mediatek-add-support-for-multiple-ports-in-media.patch 070-10-arm-dts-mediatek-add-pcie-support-for-mt7988.patch 070-11-arm-dts-medaitek-fix-internal-switch-link-speed-of-m.patch 070-12-arm-dts-mediatek-add-support-for-all-three-GMACs-for.patch 070-13-arm-dts-medaitek-add-flash-interface-driving-setting.patch 070-14-arm-dts-mediatek-update-mt7981-mmc-node.patch 070-15-MAINTAINERS-update-file-list-for-MediaTek-ARM-platfo.patch 071-01-pinctrl-mediatek-update-mt7981-pinctrl-driver-based-.patch 100-18-board-mt7629-add-support-for-booting-from-SPI-NAND.patch 290-mt7981-add-USB-nodes.patch Refreshed all the patches needing it. Run-tested: GatoNetworks GDSP, Arcadyan Mozart (ynezz), Zbt WG3526 (dangowrt) Signed-off-by: Enrico Mioso Signed-off-by: Petr Štetiar [patch refresh, Mozart testing] Signed-off-by: Daniel Golle [rebased, tested on MT7621]

sunxi: add support for Beelink X2

2025-05-29T20:56:04Z

Specifications: - SoC: Allwinner H3 Quad Cortex-A7 1.2GHz - Flash: 8GB eMMC - RAM: 1GB DDR3 - Ethernet: 1x100M - Wifi: RTL8189FTV or AP6181 - 1x USB-A Host - 1x USB-A Host/Device - 2x Button - 2x LED - HDMI, SPDIF, IR Install by following standard SD card flashing instructions. Image can also be flashed to eMMC. Signed-off-by: Kyle Hendry Link: https://github.com/openwrt/openwrt/pull/18732 Signed-off-by: Hauke Mehrtens