staging/blocktrron/package, branch master

hostapd: use subelement detail definition

2026-10-16T10:01:56Z

Use the subelement detail value definition to improve code readability. No functional change. Signed-off-by: David Bauer

hostapd: use SSID subelement definition

2026-10-16T10:01:56Z

For beacon request subelements, a dedicated mapping of types exist. Use the correct type definition to make the code more consistent. No functional change, as both definitions resolve to 0. Signed-off-by: David Bauer

qualcommax: ipq50xx: add support for Xunison Exigo Hub D50 5G

2026-10-16T07:52:28Z

The Xunison Exigo Hub D50 5G is a 5G/LTE router with Wi-Fi 6. It is also sold as the Zearts D50 5G. Specifications: SoC: Qualcomm IPQ5018, dual-core Cortex-A53 @ 1.0 GHz RAM: 512 MiB Flash: 128 MiB SPI NAND (ESMT F50D1G41LB) WLAN: IPQ5018 2.4 GHz, QCN9074 5 GHz (PCIe), both 802.11ax Ethernet: 1x GbE WAN (IPQ5018 internal GE PHY, gmac0) 3x GbE LAN (QCA8337 switch, SGMII to gmac1) WWAN: Quectel RM500Q-AE, 5G Sub-6 / LTE Cat 16, on USB 2.0 and PCIe Buttons: reset, WPS LEDs: MESH (green/red), 5G (green/red), 4G, WiFi, Internet, WAN; power is hardwired Power: 12 V / 2 A DC Serial: 115200 8N1, 4-pin header JP1 next to SW4 on the main board, from pin 1: VCC, TX, RX, GND Notes: - WAN is gmac0 wired straight to the internal GE PHY, not a switch port; its netdev is named wan by the label property. - The console RX line (gpio20) is pulled up. Left floating with nothing on the header it causes an interrupt storm and, on some units, a hang at boot. - USB is 2.0 only: the controller is limited to the HS PHY and clocks its pipe from UTMI. The 5 V supply for the port and the modem is switched by gpio24 (active low). - MACs follow the stock firmware: LAN uses 0:art 0x0, WAN 0:art 0x6. The label has no MAC printed, so there is no label-mac-device. - Wi-Fi calibration data and MAC addresses come from 0:art through nvmem cells on the Wi-Fi nodes (calibration: IPQ5018 at 0x1000, QCN9074 at 0x26800). The caldata holds the Qualcomm placeholder MAC, so the radios take the 0:art 0x0 MAC + 2 and + 3 instead. - Board data for both radios is submitted separately to firmware_qca-wireless under the calibration variant Xunison-Exigo-Hub-D50-5G, both taken from the stock firmware: bdwlan.b24-brax for the IPQ5018 and qcn9000/bdwlan.ba0 for the QCN9074. The brax file is the vendor's board variant; on my unit it outperformed the bdwlan.b24 that the stock firmware loads. - The modem power line (gpio31) has no consumer and is kept high with a GPIO hog. - The Internet LED is lit while the modem's wwan0 is up. The WiFi LED uses the network trigger in link mode, so it is lit while an AP is up on either radio; the phyNradio triggers never light it with ath11k on this board. The 4G and 5G LEDs have no trigger, as nothing in the kernel reports the modem's access technology. Modem: The RM500Q-AE is wired to both USB and PCIe, and its data_interface setting selects which one carries data. The stock firmware leaves it on PCIe (data_interface 1,0) and this port uses it there, so no AT command is needed after installing. It is driven by mhi-pci-generic with MBIM: data on wwan0, control on /dev/wwan0mbim0 and AT commands on /dev/wwan0at0. No modem interface is preconfigured; add one with the "mbim" protocol on /dev/wwan0mbim0. Installation: The factory image is a raw UBI image for the U-Boot web recovery. 1. Power the router off, hold the reset button and power it on. Keep holding until the Internet LED stays lit (about 10 seconds). 2. Set a computer on a LAN port to 192.168.1.2/24 and open http://192.168.1.254 3. Upload openwrt-qualcommax-ipq50xx-xunison_exigo-hub-d50-5g-squashfs-factory.img and wait for the router to reboot. Later upgrades use the sysupgrade image. The port started from George Moussalem's device support in the 4IceG OpenWrt tree, with the device tree reworked by Lukasz Szczur (LS3434): USB, the modem supply and the NAND/sysupgrade layout. Thanks to Hostle for the flashing work on this board and to Rafał Wabik (4IceG) for the tree it was developed in. Link: https://forum.openwrt.org/t/adding-support-for-xunison-exigo-d50-5g-zearts-d50-5g-ipq5018/247016 Co-developed-by: George Moussalem Signed-off-by: George Moussalem Co-developed-by: Lukasz Szczur <8sdasfasfas@royaleplaysempire.com> Signed-off-by: Lukasz Szczur <8sdasfasfas@royaleplaysempire.com> Co-developed-by: Rafał Wabik <4rafal@gmail.com> Signed-off-by: Rafał Wabik <4rafal@gmail.com> Signed-off-by: Steve Meek Link: https://github.com/openwrt/openwrt/pull/25890 Signed-off-by: Robert Marko

ipq-wifi: update to Git HEAD (2026-10-15)

2026-10-16T07:51:39Z

68e4bae262c0 ipq5018: add BDF for Xunison Exigo Hub D50 5G 5c5244c0b4fc qcn9074: add BDF for Xunison Exigo Hub D50 5G Signed-off-by: Robert Marko

airoha: introduce device tree overlay support for AN7583

2026-10-16T07:30:40Z

To reduce code duplication across different AN7583 evaluation boards, introduce a shared multi-EVB base device tree and utilize Device Tree Overlays (DTSO) for board-specific configurations. Signed-off-by: Yalei Zang Link: https://github.com/openwrt/openwrt/pull/24926 Signed-off-by: Christian Marangi

airoha: introduce device tree overlay support for AN7581

2026-10-16T07:30:40Z

To reduce code duplication across different AN7581 evaluation boards, introduce a shared multi-EVB base device tree and utilize Device Tree Overlays (DTSO) for board-specific configurations. Signed-off-by: Yalei Zang Link: https://github.com/openwrt/openwrt/pull/24926 Signed-off-by: Christian Marangi

uboot-airoha: enable OF_LIBFDT_OVERLAY support

2026-10-16T07:30:39Z

Enable CONFIG_OF_LIBFDT_OVERLAY for the AN7581 and AN7583 EVB defconfigs to support loading and applying device tree overlays at boot time. Signed-off-by: Yalei Zang Link: https://github.com/openwrt/openwrt/pull/24926 Signed-off-by: Christian Marangi

libjson-c: fix memory leak in json_object_put()

2026-10-15T20:06:28Z

json-c 0.19 wraps the actual object free in json_object_put() inside an assert(), so when compiled with NDEBUG (as OpenWrt does) the free is compiled out and every JSON object/array parsed by users such as ucode's json() leaks memory (~1.7KB per object). Apply the upstream fix, moving the free call outside the assert: json-c/json-c@f291fa81c6f21d925ea771a8cca597f5886309cc "free objects outside assert() in json_object_put" Fixes: https://github.com/ucode-lang/ucode/issues/495 Signed-off-by: Jo-Philipp Wich

mediatek: filogic: comfast cf-wa933: replace 128M variant with all-in-UBI

2026-10-15T20:03:42Z

Replace the expanded fixed-partition 128M target with a dedicated all-in-UBI target and OpenWrt U-Boot. Include bootloader configuration, image generation and upgrade support together. Share the fixed-partitions container and read-only 1 MiB BL2 range in the common DTSI. Declare the remaining partitions and factory NVMEM data in the variant DTS files. Keep NMBM on the legacy target and preserve its stock partition map and 64 MiB UBI region. The new layout uses a 1 MiB bl2 partition followed by a 127 MiB ubi partition, with factory and fit NVMEM/rootdisk references and redundant U-Boot environment volumes. Set the UBI variant boot arguments to `root=/dev/fit0 rootwait` and identify its fit volume as the root disk. The bootloader supplies memory and console parameters. Add the U-Boot configuration, default environment and target, recovery FIT and sysupgrade FIT images, BL2 and BL31/U-Boot artifacts, UBI environment access and FIT upgrade checks. Recognise the new compatible in board defaults. Bump the uboot-tools package release for the new environment configuration support. The installer creates fip, factory, ubootenv, ubootenv2, recovery and initial fit volumes. U-Boot and sysupgrade manage the production FIT and writable rootfs_data. DTS declarations identify volumes consumed by Linux; they do not themselves create or populate factory data. MAC address layout ------------------ Factory data is read from the legacy Factory MTD partition or the factory UBI volume; the offsets within the data are unchanged. Unit-specific address bytes are xx:xx:xx. LAN: factory offset 0xe000, mac-base cell index 0. WAN: factory offset 0xe000, mac-base cell index 1 (LAN MAC + 1). 2.4 GHz: factory offset 0x4, mac-base cell index 0. 5 GHz: factory offset 0x8000, mac-base cell index 0. Flash instructions ------------------ Conversion requires an installer; the sysupgrade ITB alone cannot convert the stock partition layout or preserve its factory data. 1. Start from the standard CF-WA933 OpenWrt target with stock MTD partitions. Back up BL2, u-boot-env, Factory and FIP with mtd dump, and copy all four files off the device before proceeding: mtd dump BL2 > /tmp/BL2.bin mtd dump u-boot-env > /tmp/u-boot-env.bin mtd dump Factory > /tmp/Factory.bin mtd dump FIP > /tmp/FIP.bin 2. Obtain the CF-WA933 installer from: https://github.com/andros-ua/owrt-ubi-installer/releases Its source and build script are available at: https://github.com/andros-ua/owrt-ubi-installer/tree/cf-wa933 Connect the PC to a LAN port and use 192.168.1.254/24; the device is at 192.168.1.1. Copy the resulting image to /tmp and run: cd /tmp sysupgrade -n \ openwrt-*-comfast_cf-wa933-ubi-initramfs-recovery-installer.itb This external installer extracts calibration/MAC data from the old Factory region before erasing it, creates and populates the static factory UBI volume, writes BL2 and fip, and creates the redundant environment, recovery and initial fit volumes. It copies one NAND eraseblock of factory data; keep the full external Factory backup. The blue WLAN LED blinks during installation and stays lit for five seconds before reboot. Run the installer only for initial conversion. 3. Once recovery boots, copy the production image to /tmp and run: cd /tmp sysupgrade -n \ openwrt-*-comfast_cf-wa933-ubi-squashfs-sysupgrade.itb To return to the legacy layout, boot the standard CF-WA933 initramfs in RAM, restore the saved BL2/u-boot-env/Factory/FIP to their original MTD partitions (using kmod-mtd-rw when needed), then sysupgrade to the standard CF-WA933 image. The restored vendor bootloader's recovery page can install vendor firmware. UART recovery of BL2/FIP is also available using https://github.com/981213/mtk_uartboot. Signed-off-by: Andrii Kuiukoff Signed-off-by: Guillaume RISCHARD Link: https://github.com/openwrt/openwrt/pull/24590 Signed-off-by: Jonas Jelonek

base-files: legacy-sdcard: don't erase extra partitions on sysupgrade

2026-10-15T08:38:14Z

Writing the full image erases partitions the image lacks. Refuse that at upgrade time unless sysupgrade -p is given, so --force and failsafe cannot bypass it, and read MBR and GPT tables the same way everywhere. sysupgrade now exports SAVE_PARTITIONS to the image check and the -p help text mentions the erase. Signed-off-by: John Audia